Daiwa TANACOM 1000 Manuel d'utilisateur

Thank you for purchasing a TANACOM 1000. To take full advantage of the reels many useful functions, please read this manual carefully before using. Re

8Names and functions of each partweakstrongloosentightenFree spool adjustmentWaterproof dragPower leverClutchLevelwindEnclosed itemsPower cord Levelwi

9   - It adjusts brake tension on the spool to prevent backlash or line slack caused by dropping the line with hook and sinker.    - You can freely ad

10Attention2.The motor can be overloaded when winding at very high tension for a long time (about 15 minutes). In this case, the motor will automatica

117MAXOFFAttention1.Do not wind the end of the line onto the spool because it causes incorrect length calculation. Move the power lever

12Line data input (With backing line)This method requires use of Daiwa braided line that is color coded to show length and has a total length greater

1379116MAXAttention2.The motor can be overloaded when winding at very high tension for a long time (about 15 minutes). In this case, the motor will au

14Line data input (Backing line 2)This procedure is to enter the line length after it has been wound onto the reel. It is necessary that you know the

157Should “Err” appear on the display, then use the MODE SET BUTTON to re-enter the data.6. Pull an additional 50m of line from the spool.7. Press the

16Functional setting operation (1. Mode setting display)1.There are many useful functions in the mode2.Use the power lever to change numerical values

172. Use the power lever to set numerical values. At its MAX position, numbers count upward rapidly. At the OFF position, numbers count downward rapid

IndexCaution   Precautions Power source   How to connect the reel to the power source   About the power source   Battery indicator Using the Reel  Abo

18Surface depth settingWhen the main line is cut or broken off...Attention1.When new line is wound up, or when line has been pulled unde

191.5m312Auto stop settingThe Auto stop depth may be set to meet your own specific needs.1. Connect the reel to the battery, and press the RESET BUTTO

20Line feeding function The line feeding function lets our line with the motor assisting the spool. - The line feeding mechanism begins to work at a d

214. Press the MODE BUTTON to go back to depth readout. 1242. Press MODE BUTTON again.3. Set speed with the power lever.1. Press MODE BUTTON. Pickup

221. Clutch OFF to send the rig to the bottomFunctional setting operation (6. Inverse counter)Inverse counter OFFTwo counters are better than one. Th

234. In the same manner, set length, waiting time and range.By pressing the JIG/PICKUP BUTTON during the jigging setting display, the display will sho

24Jigging master You can choose the number of steps you wish for your jigging pattern. Master jigging (123) is the method in which the nu

25 You can choose the waiting time between jigs. The interval time is set in seconds. The depth range for jigging is set in 1 m increments. If the ran

26Winding speed display In the default setting, the lower area counter displays the winding speed.The chumming timer display area shows the remaining

27Functional setting operation (9. Remaining time to auto stop)Displaying of the remaining time to auto stop Two counters are better than one. This re

line clipsnaplineDO NOT allow end of line to be wound onto the spool.This may cause synchronization with the levelwind to be lost, a condition that ca

128Functional setting operation (10. Chumming timer winding)Chumming timer winding The right timing for the best results. After a pre-determi

2933. Press MODE BUTTON twice.- When the display goes back to depth counter, then the procedure is completed.- The indicator is seen on the display.

30Functional setting operation (11. Display recalibration)Display revision You can recalibrate the counter should it not indicate an accurate depth co

NutCollarRod Clamprod31How to fix the Rod Clamp 1. Insert the Bolt in the clamp setting hole, and fix it by tightening the Nut and the Washer. 2. Hol

32Useful functionsVarious alarms Many kinds of information are indicated by audible alarms.Display light Backlighting of the display provides easy rea

33Reel SpecificationsReel Specification list Counter display PE6(80lb)-1000m(1100yds)PE8(100lb)-800m(880yds)PE10(120lb)-600m(660yds)PE12(150lb)-500m(5

34Parts ListTANACOM 1000TANACOM 1000No, Parts NameParts No, No, Parts NameParts No, No, Parts NameParts No,There may sometimes be a difference between

35Trouble shooting19,20923522223-25232631819,201818302110-15Symptom Possible causes To doRef. pageMotor does not respond to the power lever.Counter

Reference/Référence/HinweisInstrucciones/Riferimentihttp://www.daiwa-france.fr/ http://www.daiwa-cormoran.info/ DAIWA SPORTS LIMITEDNetherton Ind

2Power sourceHow to connect the reel to the power sourceAbout the power sourceBattery indicator1. Attach the cord clips to the battery. Red covered cl

3Using the ReelAbout the counter display1. Do not jerk your rod to free a lure or sinker stuck on the bottom. Pull the line taught with a gloved hand

4MaintenanceAbout maintenanceMaintenance procedure This is a washable reel. Wash away salt residue and grit after fishing.1. Wash the reel with a dish

5Handling and maintenance of the power cordMaintenance of the power cord Follow the restrictions below to avoid cord problems. Do not cut or connect y

6Names of the buttons and the display159846723 MODE BUTTONRESET BUTTONINVERSE COUNTER BUTTONJIG/PICKUP BUTTONMode displayDepth counterInverse counter

7  MODE BUTTONPress the MODE BUTTON to scroll through the adjustment displays for each reel function.- Use the Power Lever to adjust numeric values.-